- What size is 6AN fitting?
- ARE AN fittings the same as JIC?
- Is 6AN the same as 3 8?
- What size are fuel lines?
- How do you read a hose size?
- What size is a hose fitting?
- What are an sizes?
- How are threads measured?
- What is 8 an fitting?
- How do you determine your fitting size?
- What size is 10 an fitting?
- Is 5/8 garden hose ID or OD?
- What size hose is 8 an?
- What size wrench fits a 10 AN fitting?
- Is fuel line measured ID or OD?
- What does an fitting stand for?
- What size wrench fits a fitting?
What size is 6AN fitting?
The Good NewsMale Thread SizeAN Size*Equivalent Tube Size (Nominal OD)3/8-243AN3/16″7/16-204AN1/4″9/16-186AN3/8″3/4-168AN1/2″3 more rows•Jul 25, 2012.
ARE AN fittings the same as JIC?
JIC fittings are dimensionally identical to AN (Army-Navy) fittings, but are produced to less exacting tolerances and are generally less costly. SAE 45-degree flare fittings are similar in appearance, but are not interchangeable, though dash sizes 2, 3, 4, 5, 8, 10, 14, and 16 share the same thread size.
Is 6AN the same as 3 8?
No they aren’t exactly the same. Most people compare them because they are close and flow roughly the same. According to this, AN and hard line are OD measurements and NPT is inside diameter so for AN and hard line the inside diameter would depend on the thickness of the tubing.
What size are fuel lines?
Most stock applications came with 5/16-inch fuel line, but for many street vehicles and mild race applications 3/8-inch (AN 6) fuel line is a good upgrade. High performance applications and racers using alcohol will use 1/2-inch (AN 8) fuel line.
How do you read a hose size?
Simply put, a dash size refers to an I.D. of a hydraulic hose or fitting in 1/16″ increments. For example, -6 hose would indicate a hose with I.D. of 6/16″ – or 3/8″. Hoses are measured by inside diameter, unlike tubes which are measured by outside diameter.
What size is a hose fitting?
In the United States, most standard garden hoses are 5/8 inch in diameter.
What are an sizes?
The AN thread is a particular type of fitting used to connect flexible hoses and rigid metal tubing that carry fluid. … AN sizes range from -2 (dash two) to -32 in irregular steps, with each step equating to the OD (outside diameter) of the tubing in 1⁄16-inch increments.
How are threads measured?
StepsMeasure an inch-long portion of the threaded area. Grab a ruler and lay it along the bolt or screw. … Count the number of threads in 1 inch. … Measure the diameter and the length of the threaded area. … Plug the information into a standard measurement.
What is 8 an fitting?
“AN” Thread Sizes For example, an -8 AN fitting translates to an 8/16 inches, or 1/2-inch.
How do you determine your fitting size?
You can always identify AN fittings based on the male thread size (outside diameter). These sizes are constant regardless of brand, hose type, or fitting configuration. If your fitting has a convex 37 degree flare at the end, the threads will tell you the AN size (and vice-versa).
What size is 10 an fitting?
Plumbing Basics – AN Fittings & HosesAN SizeHose i.d. – Tube o.d.SAE Thread Size-81/2 in.3/4 in.-16-105/8 in.7/8 in.-14-123/4 in.1 1/16 in.-12-161 in.1 5/16 in.-129 more rows•Aug 28, 2001
Is 5/8 garden hose ID or OD?
In the United States, most standard garden hoses are 5/8 inch in diameter. The bigger the diameter, the more water is delivered.
What size hose is 8 an?
Russell Performance Technical SupportAN SizeMetal Tube O.D.Thread Size-5 AN5/16″1/2″ – 20 SAE-6 AN3/8″9/16″ – 18 SAE-8 AN1/2″3/4″ – 16 SAE-10 AN5/8″7/8″ – 14 SAE5 more rows
What size wrench fits a 10 AN fitting?
Stainless Tubing AN EquivalentStainless Tubing AN Equivalent All dimensions are in inches unless otherwise noted.ANTube Size ODWrench Size-105/8″1″-123/4″1 1/4″-161″1 1/2″10 more rows•Dec 31, 2014
Is fuel line measured ID or OD?
Tubing is OD (outside diameter) and Pipe is ID (inside diameter). So the easiest way to tell the size of your fuel line, which is tubing, is to use a combination wrench. Whichever one slips over snuggly is the winner.
What does an fitting stand for?
Air Force – Navy Aeronautical Design StandardsHistorical Context of the AN Fitting AN stands for Air Force – Navy Aeronautical Design Standards (also known as “Army Navy”) that are used in U.S. Military aviation applications. These fittings are made to meet strict performance standards related to the aeronautical industry.
What size wrench fits a fitting?
Hex) Standard Fittings.